- Parts needed to build a Mighty Mini or Super Mighty Mini, this is not a definitive list, but it does give you a very good idea of what is needed to build your own Mighty Mini race car. All parts are available from most Mini parts stockist.
MIGHTY MINIS CLASS ‘A’ & ‘B’
- Roll Cage: Safety Devices 6 point cage six-point Safety Devices roll cage with a fixed or removable diagonal bar.
- Door bars x 4 . 2 per side
- Horizontal bar linking the two roll cage rear upright legs Part No:
- Harness bar
- Horizontal bar linking the two roll cage front upright legs Part No:
- Windows: The door windows, rear quarter windows and rear windscreen must be 4mm poly carbonate (NOT PERSPEX)
- Front bumper: Front bumper an undamaged Mighty Minis racing bumper. Part no: (FB-007)
- Fibreglass Boot lid:The boot lid Part No:
- Class A Engines
- Valve guides Part No:
- The inlet manifold locating ring Part no:
- Exhaust valve size Part no: (tam1061)(triple groove collett).
- Inlet valve size Part no: (tam1058)(triple groove collett).
- Double valve springs Part No: .
- Gearbox Part no: (TRC10086N)
- The cylinder head Part no’s: (LDF10197) or MPi (LDF-105380),
- The engine block can be a non SPi 1275 A plus.
- Pistons Part No: (TAM2050) or hepolite Part No: (P21253) or Nural Part No:87-524107-00.
- Camshaft Part No: (LGC10230) and Part No: (MM-1660S).
- Connecting rod bolts Part No: (
- Thick walled rocker shaft. Part No:
- Valve springs Part No:
- Main bearings Vandervell bearings. Part No: . Or an ACL
- Big end bearings Vandervell bearings. Part No: ( Or an ACL equivalent
- Head gasket. Part No’s: ().
- Adjustable oil pressure valve Part No: ().
- Block to oil filter feed pipe Part No: ().
- Central oil pick-up pipe, Part No: ().
- Magnetic trap at the rear of the gearbox Part No’s: ().
- Aftermarket fans
- Single camshaft timing gear Part no:
- Crankshaft timing gear Part no:
- Class A Exhaust
- The exhaust manifold Maniflow LCB part no
- Single or twin silencer box equipped RC40 or a Maniflow system. Not exceeding 1.7/8 inches overall diameter size.
- Ignition: ECU Part No’s: (MNE10027, MNE10092, MNE 101070, MNE101170)
- Suspension & steering
- Front sub-frame to floor mountings Part no: (
- Front and rear (shock absorbers) GAZ adjustable units. Font lowered Part No: ) rear lowered Part no: (C-.
- Front suspension lower arms Part no: or Part no:
- Front suspension tie bars Part no:
- Front sub-frame tie bar rubbers part no:
- Front sub-frame lower arm rubbers Part no:
- Font and rear rubber suspension springs Part no: .
- Steering arms Part no:
- Transmission
- Baulk rings Part No: (
- Layshaft Part No: (
- Quick shift gear change mechanism. Part No: .
- Stabiliser bar Part no: (
- Brakes: Front callipers Part no: (
- Tyres: Tyre Part no: YOKOHAMA A539, 165.60.12 71H
SUPER MIGHTY MINIS CLASS ‘B’
- Engines
- The engine block can be a non SPi 1275 A plus.
- The cylinder head Part no: (SMM168),
- Gearbox Part no: (TRC10086N)
- Standard valve springs can only be replaced by double valve springs Part No: .
- For single groove valves, valve caps Part no: ().
- For triple groove valves, valve caps Part no: ().
- Inlet valve size 35.6 mm Part no: (TAM 1059) (triple groove collett).
- Exhaust valve size 29.4 mm Part no: (TAM 1061) (triple groove collett).
- Inlet valves size 35.6 mm Part no: () (single groove collett) with the colletts Part no: (88G459)
- Exhaust valves size 29.4 mm Part no: (CAM 4601) or (C-AEG106) (single groove collett) with the colletts Part no: ().
- Inlet manifold locating ring Part no: (
- Omega Pistons Part no: ()
- Push rods Part no: ).
- Camshaft Part No’s: ().
- Connecting rod bolts Part No: ().
- Thick walled rocker shaft.
- Cam followers Part No:
- Adjustable oil pressure valve.
- 1.5 Roller tip rockers P
- Crankshaft pulley Cooper ‘S’ version Part No’s: (retaining bolt & washer)
- Alloy Rocker cover
- Crankshaft timing gear Part no:
- Adjustable oil pressure valve Part No:
- Block to oil filter feed pipe Part No: (.
- Central oil pick-up pipe, Part No: .
- Magnetic trap at the rear of the gearbox Part No’s: ().
- Aftermarket cooling fans Part no’s:
- Camshaft MM 1608
Exhaust: The exhaust manifold Maniflow LCB Part no ).Exhaust system twin or single silencer box equipped Maniflow system not exceeding 2 inches over all diameter Part No’s: (
Ignition:ECU Part no’s: (MNE10027, MNE10092, MNE 101070, MNE101170)
- Suspension & Steering
- Front sub-frame to floor mountings Part no ().
- Front and rear (shock absorbers) GAZ adjustable units. Font lowered adjustable bump and rebound Part no: () rear lowered Part no: ().
- Font and rear rubber suspension springs part no: ().
- Steering arms Part no: ().
- Font and rear rubber suspension springs part no: ().
- Steering arms Part no: ().
- Rear anti-roll bar Part no: ()
- Longer drop links Part no: ()
- The front and rear rubber suspension springs Part no: ()
- Steering rack 2.2 turns. Part no: ()
- Transmission
- Baulk rings Part No: ().
- Layshaft Part No: ().
- Quick shift gear change mechanism. Part No: ().
- Stabilising bar Part no: ().
- 23 tooth primary gear
- 23 tooth input gear Part No: ()
- 30 tooth idler gear Part no: ()
The gear cluster is a straight gear kit as listed below:
First motion
First gear Second gear Third gear Lay gear |
20
31 26 23 15/19/23/25 |
Differential ratio is the 3.4:1 Part no: CWP3-4
Brakes: Front callipers
Tyres: Control tyre is Part no: YOKOHAMA A 048R 165.55.12.71H